Can I Use Gun Oil on an Airsoft Gun

Equally with firearm maintenance, airsoft guns too need some TLC from time to time, and the purpose of this web log is to educate you - the airsoft enthusiast - as to when and how this maintenance should occur.

Beginning, to articulate up a common misconception... airsoft guns are Not to exist lubricated with WD-twoscore or gun oil. The proper lubricant for airsoft guns is high class silicone oil. (I personally employ Premium P-Force airsoft silicone performance lubricant in a spray bottle). Anything else will attract particles and dirt, foul your barrel and internals, and crusade corrosive damage to your airsoft gun. Utilise silicone oil spray exclusively.

Cleaning The Butt:

Airsoft gun barrels do occasionally demand to be cleaned, and an indication of 'as to when' lies in the flight-path of your airsoft gun Bulletin board system. If the airsoft pellet is deviating vertically, so it's time to recall your cleaning rod and a pocket-sized piece of quality paper towel which you'll thread through the tip of the rod (every bit you would thread through a needle – the strip of the paper towel should be approximately ½" broad by 3" long), and grab your silicon lubricant. Lightly spray the strip, and and so insert the cleaning rod strip-first into the butt, spinning the rod as you lot gently movement it kickoff downward the length of the butt, and and then dorsum out. Following this, thread a clean strip of paper towel into the tip of the cleaning rod and echo the procedure (this volition remove any excess silicon oil from the butt, and leave it obstruction-free).

Lubricating the Hop Upwardly and Gearbox:

For issues with airsoft AEGS mis-feeding or jamming, occasionally an airsoft gun's hop up needs to be lubricated. To practise this, remove the gun'south mag and fire ii to three times in semi-machine to assure that the hop upwards is free of airsoft Bulletin board system, and then identify the gun on your lap, upside down. With your bottle of silicon oil, angle the bottle and accompanying spray tube (which you've already inserted into the bottle'south nozzle) into the hop up, and spray ane to two times. Be sparing with the oil (yous don't want to utilise too much), and let the gun sit down for five minutes, allowing the silicone to seep into the hop up.

As with the hop up, your gearbox may occasionally demand to be lubricated as well (although given that gearboxes comes from their corresponding manufacturers packed with industrial-grade grease or white lithium, this blazon of maintenance rarely needs to be performed. If your gearbox is whining, this may however do the trick). To lubricate the gearbox, the motor will get-go need to be removed from the airsoft electric gun, and in one case that chore is completed, a small hole in the lesser of the gearbox will be visible by peering into the at present-hollow gun handle. Place the tip of the spray tube through the handle and just into the visible gearbox hole, and spray three to four times. Over again, leave the AEG upside-down so as to permit the silicon oil to work its mode into the airsoft gearbox.

Lubricating Gas & C02 Airsoft Guns:

Silicone oil is a needed accessory for gas and c02 airsoft guns, peculiarly of the blowback multifariousness. As gas airsoft magazines rely on rubber gaskets and O-rings to perform, they need to oft be lubricated with silicone oil in order to retain the gasket's expansion, which will assist the gas gun in properly operating (and which will go on the gas from venting or releasing prematurely). In lodge to lubricate a gas mag, spray silicone oil into the port at the top of the mag, then work the valve on the side back and forth for approximately i infinitesimal. This procedure will allow the oil to seep downwards onto the gasket. Lubricating the gas magazine's fill port on the lesser of the magazine should likewise be conducted. In society to do and then, hold the mag upside down, and inserting the tip of the spray tube into the make full port, spray one to two times. Let the oil to work its way into the fill-port gasket by leaving the mag upside-down for five minutes or and so before loading the mag with gas and testing.

c02 airsoft guns and mags occasionally need to be lubricated equally well. Using the spray canteen, lubricate the mag'due south gasket at the betoken where it comes into contact with the c02 cylinder (for c02 guns where the cylinder is inserted directly into the gun's pistol grip, similarly lubricate the gasket which comes into contact with the cylinder). You'll want to wait a minimum of ten minutes before testing, every bit annihilation prior volition prevent the oil from working its style effectively into the rubber seals (c02 is cold and volition cause the oil to become dense).

The slide runway of both gas and c02 airsoft blowback guns may occasionally demand to be lubricated too, in club to let for proper slide traversal. To practise so, remove the slide, and lightly spray all contact points betwixt the slide and the gun body, and then reattach the slide. This will provide proper lubrication and allow for an environment nearly devoid of friction.

Nearly the Writer: Mike Zhang is the President and COO of Airsoft Megastore, an airsoft retailer offering electrical and gas powered airsoft guns. Delight visit Airsoft Megastore to store for airsoft green gas guns and total metal airsoft rifles for players of whatever experience level.

Labels: airsoft gun lubrication, cleaning airsoft gun, how to clean an airsoft gun